Certified, insured mold cleanup with a written clearance report

Professional Mold Removal in SYLMAR, California

Professional Mold Removal in SYLMAR, California means finding the moisture source, containing the growth, and removing contaminated material instead of painting over it. We handle expert mold remediation SYLMAR California for homeowners and property managers dealing with attic growth, crawl space contamination, bathroom recurrence, and post-flood damage. Call (833) 929-5837 and we will be on site the same day.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dependable Mold Remediation Service across SYLMAR, California
Careful work. Honest options.
About this service

What Professional Mold Removal in SYLMAR, California Involves

Professional Mold Removal in SYLMAR, California is a containment-and-removal process, not a cleaning service. We start with a moisture meter and a thermal imaging camera to trace where water is actually entering, then map the spread with a boroscope inspection camera inside walls and under floors. Once we know the footprint, we build a containment barrier with plastic sheeting, run an air scrubber with HEPA filters to hold spore counts down, and remove contaminated drywall, insulation, and framing. Surfaces get an antimicrobial solution and an encapsulant coating so the growth does not return.

SYLMAR homes sit in a dry climate that hides water problems until they are serious. A slow supply-line leak under a slab, a swamp cooler pan that overflows each summer, or a roof flashing failure during winter rain all feed hidden growth for weeks. That is why we see so much attic mold and crawl space mold here. If you need affordable expert mold remediation in SYLMAR CA, we test first, show you the readings, and only then quote the work. No guesswork, no scare pricing.

  • ✓ Same-Day Emergency Response
  • ✓ Documented Clearance Testing
  • ✓ Licensed and Insured Crews
  • ✓ Source Fix, Not Just Cleanup
What's included

What Professional Mold Removal Includes

Every job includes inspection, containment, removal, treatment, drying, and clearance testing. We do not itemize containment or equipment as add-ons. What varies is the scope of material removal, which we determine after the inspection and put in writing before we start.

✓

Full Inspection and Moisture Mapping

Moisture meter and thermal imaging camera readings on every affected surface, plus boroscope inspection inside wall cavities. You get photos and a written summary the same day, before any work begins.

✓

Containment and Negative Air

Containment plastic sheeting sealed at all seams, with an air scrubber running HEPA filters under negative pressure. This keeps spores from spreading to clean rooms during removal.

✓

Removal of Contaminated Material

Drywall, insulation, and porous material removed in sealed bags and disposed of properly. Structural framing cleaned with a HEPA vacuum, then treated with an antimicrobial solution and encapsulant coating.

✓

Drying to Below 16 Percent

Dehumidifiers and air movers run until framing moisture reads below 16 percent on the meter. We do not close a job on a wet structure, because that is how mold comes back.

✓

Post Remediation Clearance Testing

Spore trap sampling compared to outdoor baseline, with lab results in writing. This is the document insurers, buyers, and landlords want to see before they consider the job closed.

How it works

How Our Mold Removal Process Works

01

Inspection and Testing

We walk the property with a moisture meter and thermal imaging camera, then take air samples with a spore trap sampler and surface samples where growth is visible. You get readings and photos the same day. This step takes 45 to 90 minutes on a typical SYLMAR home.

02

Containment Setup

We seal the work area with containment plastic sheeting and negative air pressure so spores cannot migrate into clean rooms. An air scrubber with HEPA filters runs continuously. On a 200-square-foot attic or bathroom job, containment setup takes about two hours.

03

Removal and Cleaning

Contaminated drywall, insulation, and porous material come out in sealed bags. Structural framing gets HEPA vacuuming, then an antimicrobial solution, then an encapsulant coating. For heavy surface growth on joists and subfloor, we use dry ice blasting mold removal, which strips growth without adding moisture.

04

Drying and Verification

Dehumidifiers and air movers run until framing moisture reads below 16 percent on the meter. We do not close out a job on a wet structure. Drying typically takes 24 to 72 hours depending on how saturated the material was when we started.

05

Clearance Testing and Report

We run post remediation mold testing with a spore trap sampler and compare indoor counts against an outdoor baseline. You receive the lab report and a written scope of what was removed and what was treated. If clearance fails, we re-clean at no additional cost.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture Meter

Reads moisture content in drywall, framing, and subfloor. We use it to find hidden water and to confirm the structure is dry before we close a job.

Thermal Imaging Camera

Shows temperature differences that reveal hidden moisture behind walls and under floors. It finds water you cannot see with the naked eye.

Boroscope Inspection Camera

A small camera on a flexible probe that lets us inspect inside wall cavities and under floors without tearing everything open.

Air Scrubber with HEPA Filters

Runs continuously during removal to capture airborne spores and hold the containment under negative pressure. We use Abatement Technologies units.

Spore Trap Sampler

Collects air samples for lab analysis. Used for both pre-remediation testing and post remediation clearance testing.

Dry Ice Blasting Machine

Strips mold from framing and subfloor without adding moisture or damaging wood. Used on structural lumber where abrasive methods would be too aggressive.

Dehumidifier and Air Movers

Dri-Eaz and Phoenix Restoration equipment that dries the structure below 16 percent moisture before treatment. Drying is what makes the fix hold.

Real results

Before and after.

Attic Remediation After Roof Leak

Before

A 1,100-square-foot SYLMAR home had a roof flashing failure that went unnoticed for two months. By the time the homeowner smelled mustiness, mold had spread across roughly 200 square feet of attic sheathing and saturated the insulation.

After

We contained the attic, removed the contaminated sheathing and insulation, HEPA vacuumed and treated the framing, and ran drying equipment for three days. Post remediation testing came back below outdoor baseline, and the homeowner had a clearance report for their insurance claim.

Crawl Space Cleanup After Flooding

Before

A property near the Pacoima Wash Area took on water during winter storms. The crawl space insulation was saturated, and growth had started on the floor joists within a week. The homeowner was concerned about air quality in the living space above.

After

We removed the saturated insulation, dried the framing below 16 percent moisture, and treated the joists with an antimicrobial solution and encapsulant coating. Air sampling after remediation showed spore counts within normal range, and the homeowner had documentation for their records.

Bathroom Recurrence Solved

Before

A tenant in a multi-unit property on Maclay Avenue had mold returning around the bathroom window every few months despite repeated cleaning. The landlord had tried bleach and paint, but the growth came back within weeks each time.

After

We removed the growth, treated the surfaces, and found the exhaust fan was undersized and venting into the wall cavity. After fixing the vent and treating the wall, the bathroom cleared testing and has had no recurrence in eight months.

Problems we solve

Mold Problems We Solve in SYLMAR

Most of the calls we get are about the same handful of problems. Here is what they look like and what we do about them.

Ask a pro →
01

Musty odor that will not go away

We trace the odor with a moisture meter and thermal imaging camera, then confirm with air sampling. Once we locate the source, we contain the area, remove the growth, and treat the surfaces. The smell goes away because the growth is gone, not because we masked it.

↗
02

Bathroom mold that keeps coming back

We remove the growth, treat the surfaces with an antimicrobial solution, and identify the ventilation problem. We tell you exactly what to fix, whether it is the fan, the ducting, or the caulking, so the fix holds instead of repeating.

↗
03

Attic mold after a roof leak

We test the attic, contain the work area, and remove contaminated sheathing and insulation. Framing gets HEPA vacuuming and an encapsulant coating. We coordinate with your roofer on the source repair so the leak is fixed before we close out.

↗
04

Crawl space mold and high humidity

We remove the growth, treat the framing, and identify the moisture source, whether it is a plumbing leak, poor drainage, or ground vapor. We dry the space below 16 percent moisture before treating, so the remediation holds.

↗
Proof you can check

Licensed, Certified, and Documented

✓
IICRC CertificationInstitute of Inspection, Cleaning and Restoration Certification
✓
ACAC CertificationAmerican Council for Accredited Certification
✓
State Contractor LicenseCalifornia Contractors State License Board
✓
EPA Mold Remediation Guidelines ComplianceU.S. Environmental Protection Agency
✓
California Department of Public Health Mold GuidelinesCalifornia Department of Public Health
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs in SYLMAR run $1,200 to $4,800 in 2026, with small bathroom or attic scopes starting around $850. Crawl space and post-flood jobs with extensive material removal can reach $8,000 or more. Price depends on square footage affected, material type, and access. We quote a flat number after the inspection, not a range that moves.

Look for IICRC certification, a state contractor license, and proof of liability insurance. Ask whether containment and negative air pressure are included, and whether you get written clearance testing at the end. A company that skips containment or will not put clearance in writing is leaving spores and liability behind. Ask for the lab report before you pay.

Ours is. We carry full liability and workers comp coverage, and we will provide a certificate of insurance on request before work begins. Insured mold removal SYLMAR protects you if a technician is injured on your property or if something is damaged during removal. Never hire a mold crew that cannot produce a COI the same day.

A single bathroom or small attic typically takes two to three days. Crawl space jobs and post-flood remediation usually run four to seven days because drying takes longer. Containment setup is about two hours, and drying runs 24 to 72 hours. You get a day-by-day schedule in your scope before we start.

Ready when you are

Get Professional Mold Removal in SYLMAR, California Today

Call (833) 929-5837 and we will inspect, test, and quote the same day. Licensed, insured, and IICRC-certified, with written clearance testing on every job. If you are searching for licensed mold remediation for homeowners SYLMAR CA, this is the call to make.

Call Now (833) 929-5837 →
Request an appointment

Contact Our Sylmar Team

Call (833) 929-5837 or send us a message and we will get back to you the same day. Our phones are answered 24 hours for emergencies, and regular inspections are scheduled Monday through Friday. Tell us what you are seeing or smelling, and we will tell you what the next step is.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837