Certified mold removal contractor for homes and businesses

Mold Remediation Company in SYLMAR, California

When black mold shows up behind drywall or under a crawl space, you need a Mold Remediation Company in SYLMAR, California that finds the water source first. Our certified mold remediation company SYLMAR California handles inspection, containment, removal and clearance testing for homeowners and property managers across the San Fernando Valley. Call (833) 929-5837 and we will tell you what is growing and why.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Mold Remediation Service Sylmar serving SYLMAR, California
Careful work. Honest options.
About this service

What a Mold Remediation Company in SYLMAR, California Does

A Mold Remediation Company in SYLMAR, California is a licensed and certified contractor that locates mold growth, fixes the moisture problem feeding it, removes contaminated materials, and verifies the air is clean afterward. That is different from a cleaning crew with a spray bottle. We open walls, run a boroscope inspection camera through framing, measure moisture with a moisture meter, and map the full extent of growth before anything gets torn out. Then we build containment, run air scrubbers with HEPA filters, and remove the mold at the source.

Most SYLMAR homes we walk into have the same story: a slow supply-line leak under a kitchen sink, a swamp cooler pan that overflowed last summer, or a crawl space that stays damp because the soil never dries out. Add a 100-degree August and that moisture turns into visible growth in 48 to 72 hours. If you have been searching for a mold cleanup company SYLMAR residents trust, we handle the whole job, from the first moisture reading to the final post remediation mold testing.

  • ✓ Source Fixed, Not Just Sprayed
  • ✓ Containment That Protects Your Home
  • ✓ Clearance Testing Before We Leave
  • ✓ Insurance Paperwork Handled
What's included

What Our Mold Remediation Service Includes

Every job includes the full sequence: inspection, containment, removal, treatment, drying and clearance testing. Rebuild like drywall, texture and paint is available as an add-on so you are not coordinating a second contractor. Here is what is covered on a standard scope.

✓

Full Moisture and Mold Inspection

Moisture meter and thermal imaging camera readings on every suspect surface, plus boroscope inspection camera access into wall cavities. You get photos and a written scope before any work begins.

✓

Sealed Containment and Negative Air

Containment plastic sheeting with zipper doors, air scrubbers with HEPA filters and negative air machines running continuously. This keeps spores out of the rest of your home during removal.

✓

Contaminated Material Removal

Removal of affected drywall, insulation and porous materials, bagged and hauled out as construction debris. Salvageable framing gets HEPA vacuuming and antimicrobial solution treatment.

✓

Antimicrobial and Encapsulant Treatment

Application of EPA-registered products from Concrobium, Benefect and RMR Solutions, followed by encapsulant coatings on framing where the substrate calls for it. Fogging is used in wall cavities and ductwork.

✓

Structural Drying

Dehumidifiers and air movers run until framing and substrates read dry on a moisture meter. This step is what prevents the growth from returning once the containment comes down.

✓

Third-Party Clearance Testing

Spore trap sampler testing through an independent lab after remediation. You receive the written lab report showing indoor counts compared against outdoor baseline. We do not clear our own work.

How it works

How Our Mold Remediation Process Works

01

Inspection and Testing

We arrive within the scheduled window, walk the property with you, and run a moisture meter and thermal imaging camera on every wall, ceiling and floor that could be wet. A boroscope inspection camera goes into wall cavities. Air samples go to a third-party lab. You get results in 24 to 48 hours.

02

Containment and Air Scrubbing

Once we know the scope, we build a sealed work zone with containment plastic sheeting and zipper doors. Air scrubbers with HEPA filters and negative air machines run 24/7 to keep spore counts down inside the containment. This step usually takes two to four hours to set up.

03

Removal and Disposal

We remove contaminated drywall, insulation and any porous material that cannot be saved. Technicians wear personal protective equipment and respirators. Salvageable framing gets HEPA vacuuming, then an antimicrobial solution and encapsulant coatings. Everything bagged goes out as construction debris, not through your kitchen trash.

04

Treatment and Drying

We apply EPA-registered products from brands like Concrobium and Benefect, and where the surface calls for it we use a fogging machine or dry ice blasting machine. Dehumidifiers and air movers run until structural moisture reads dry. That typically takes two to four days depending on how wet the framing is.

05

Clearance and Rebuild

A spore trap sampler verifies the air is clean. Once the lab clears the job, we can hang new drywall, tape, texture and paint so you are not chasing a second contractor. Most full jobs, from containment to paint, run five to ten working days.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture Meter

Pin and pinless readings on drywall, framing, subfloor and concrete. This is how we find wet material behind a wall that looks and feels dry on the surface.

Thermal Imaging Camera

Infrared scanning reveals temperature differences caused by hidden moisture. We use it to map the full extent of a leak before we open anything up.

Boroscope Inspection Camera

A small camera on a flexible shaft that goes into wall cavities, ductwork and crawl spaces through a drilled hole. It lets us see growth without tearing out a whole wall.

Air Scrubber and HEPA Vacuum

Air scrubbers with HEPA filters keep spore counts down inside containment. HEPA vacuums remove settled spores from framing and surfaces without re-releasing them into the air.

Dehumidifier and Air Mover

Dri-Eaz and Phoenix Restoration units pull moisture out of framing and substrates. Structural drying is what stops the growth from returning after remediation.

Fogging Machine

Applies antimicrobial solution as a fine mist into wall cavities, ductwork and voids that cannot be reached by hand. Used as a supplement to physical removal, never as a replacement.

Dry Ice Blasting Machine

Removes mold from framing, concrete and brick without water or abrasive media. Ideal for structural surfaces where sanding would damage the material or spread spores.

Spore Trap Sampler

Collects airborne spores for laboratory analysis. Used at the start of a job to establish baseline and again at the end for clearance testing.

Real results

Before and after.

Crawl Space Mold on Dronfield Avenue

Before

A 1955 raised-foundation home had visible white and black growth across the floor joists and subfloor. Insulation was saturated and hanging loose. Moisture meter readings on the joists were above 25 percent, and the crawl space had no vapor barrier.

After

We removed all contaminated insulation, HEPA vacuumed the framing, applied antimicrobial solution and encapsulant coatings, and installed a new vapor barrier. Post remediation mold testing came back at normal background levels. The job took five days.

Bathroom Mold Behind Shower Wall

Before

A failed shower pan had been leaking into the wall for months. Drywall on the back side of the shower was soft and covered in black mold growth. The adjacent bedroom smelled musty, and the homeowner had already cleaned the visible surface twice with no lasting result.

After

We contained the bathroom and bedroom wall, removed the affected drywall and insulation, treated the framing, and dried the cavity. New drywall, tile backer and paint went in after clearance. Total job ran seven working days.

Attic Sheathing Mold After Winter Rains

Before

A home near Olive View had dark staining across roughly 400 square feet of roof sheathing. The attic had no ridge vent and only two small gable vents. A boroscope inspection confirmed active growth on the sheathing and the top plates of the interior walls.

After

We set containment in the attic, HEPA vacuumed and dry ice blasted the sheathing, then applied antimicrobial solution and encapsulant coatings. A roofer added ridge and soffit ventilation. Clearance testing passed on the first sample.

Problems we solve

Mold Problems We Solve for SYLMAR Homeowners

Most mold calls start with a water problem the owner did not know about. Here are the situations we run into most often in SYLMAR, and what happens if they get ignored.

Ask a pro →
01

Crawl space mold from soil moisture and poor ventilation

We remove contaminated insulation and debris, HEPA vacuum the framing, treat with antimicrobial solution and encapsulant coatings, then address the soil moisture and ventilation that caused the problem. Most crawl space jobs take three to five days including drying.

↗
02

Bathroom mold recurrence after cleaning

We open the wall, find the failed caulk line, leaking shower pan or blocked exhaust, and remove the contaminated drywall and insulation. Then we treat the framing and tell you exactly what to fix so it does not come back. Typical scope is $1,500 to $3,500.

↗
03

Attic mold from roof deck condensation

We test the sheathing, remove growth with HEPA vacuuming and dry ice blasting where the surface calls for it, then treat with antimicrobial products. We also document the ventilation shortfall so your roofer can correct it.

↗
04

HVAC mold contamination spreading through the house

We inspect the air handler, ductwork and returns, then remediate the contaminated sections and fog the duct system. We also recommend a duct cleaning and filter upgrade so the system does not recontaminate the home after we leave.

↗
Proof you can check

Licensed, Certified and Reviewed

✓
IICRC CertificationInstitute of Inspection, Cleaning and Restoration Certification
✓
ACAC CertificationAmerican Council for Accredited Certification
✓
State Contractor LicenseCalifornia Contractors State License Board
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
✓
Indoor Air Quality CertificationAmerican Council for Accredited Certification
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs in SYLMAR run $1,500 to $6,500 in 2026, with small bathroom or attic scopes starting around $1,200 and full crawl space or multi-room jobs reaching $10,000 or more. Price depends on square footage affected, how deep the growth goes into framing, whether HVAC contamination is involved, and whether rebuild is included. We give you a fixed written price after inspection, not a range that moves.

Ask three things: are they licensed and insured in California, do they hold IICRC or ACAC certification, and do they do third-party clearance testing. A contractor who tests their own work has a conflict of interest. Also confirm they will fix the moisture source, not just remove visible growth. If a company quotes over the phone without seeing the property, keep calling.

Yes. Sudden and accidental water damage, like a burst supply line or appliance failure, is usually covered by homeowner policies. Long-term neglect and gradual leaks typically are not. We document the loss with photos, moisture readings and lab results, then bill your carrier directly when coverage applies. You pay your deductible and we handle the paperwork.

At minimum, IICRC certification in water damage restoration and applied microbial remediation, plus a current California state contractor license and liability insurance. ACAC certification is a strong signal for air quality work. Ask to see the certificate and the license number. Our technicians carry IICRC certification and we follow EPA mold remediation guidelines and California Department of Public Health mold guidelines on every job.

Ready when you are

Call Your Mold Remediation Company in SYLMAR, California

We answer the phone, we show up when we say we will, and we give you a fixed price before we cut anything. Licensed, insured and warrantied. Call (833) 929-5837 now and we will schedule your inspection today.

Get Free Estimate (833) 929-5837 →
Request an appointment

Contact Our Sylmar Team

Call (833) 929-5837 or send us a message and we will get back to you the same day. Our phones are answered 24 hours for emergencies, and regular inspections are scheduled Monday through Friday. Tell us what you are seeing or smelling, and we will tell you what the next step is.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837