Certified crews, same-day response, and clean air you can prove

Mold Remediation near me in SYLMAR, California

If you are searching for Mold Remediation near me in SYLMAR, California, our IICRC-trained crews handle the inspection, containment, and removal in one visit. We serve homeowners and property managers from San Fernando Road Corridor to Lopez Canyon, and we test the air before and after so you know the spores are gone. Most jobs start the same day you call.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Mold Remediation Service Sylmar serving SYLMAR, California
Careful work. Honest options.
About this service

What Mold Remediation near me in SYLMAR, California Involves

Mold Remediation near me in SYLMAR, California is the process of containing, removing, and cleaning mold growth so indoor spore counts drop back to normal outdoor levels. It is not wiping a wall with bleach. We map the moisture with a moisture meter and thermal imaging camera, build a containment barrier around the affected area, run air scrubbers with HEPA filters, and remove contaminated drywall and insulation rather than painting over it. Every job ends with post-remediation verification testing.

SYLMAR homes deal with two mold seasons, not one. Winter rain pushes water through 1950s stucco and flat roofs, and summer heat drives indoor humidity past 60 percent in garages and crawl spaces. That is why so many people here search for mold removal near me SYLMAR California after a leak they forgot about. If you need emergency mold remediation near me SYLMAR 24/7, we answer the phone and dispatch a crew, not a call center.

  • ✓ Air You Can Breathe
  • ✓ Same-Day Crew Dispatch
  • ✓ Damage Stopped at the Source
  • ✓ Documented for Insurance
What's included

What Is Included in Our Mold Remediation Service

Every job we run includes the full sequence: inspection, containment, removal, cleaning, and clearance testing. We do not sell those as separate line items, because skipping any one of them means the mold comes back. Here is what you get when you book us.

✓

Full Moisture Inspection

We run a moisture meter and thermal imaging camera across every suspect wall, ceiling, and floor, plus a boroscope inspection camera into cavities. This takes 30 to 45 minutes and tells us the real footprint, not just the visible stain.

✓

Sealed Containment Setup

We build a 6-mil containment barrier with zip-wall doors and run air scrubbers with HEPA filters under negative pressure. Setup takes about 45 minutes on an average job and keeps spores out of the rest of your home.

✓

Contaminated Material Removal

Moldy drywall and insulation come out and get bagged for disposal. Structural framing gets HEPA vacuuming, antimicrobial solution, and an encapsulant coating where needed. We remove, we do not paint over.

✓

HEPA Vacuum and Antimicrobial Treatment

Every surface inside the containment gets HEPA vacuumed, then treated with an antimicrobial solution such as Concrobium or Benefect. On heavy jobs we finish with a fogging machine to reach cavities and HVAC chases.

✓

Post-Remediation Clearance Testing

We sample air inside the containment and outside as a baseline using spore trap samplers. If indoor counts are at or below outdoor levels, the job passes. Lab results arrive within 24 to 48 hours, in writing.

How it works

Our 5-Step Mold Remediation Process

01

Phone Triage

We ask three questions: where you see or smell the mold, how long it has been there, and whether there was a leak or flood. That tells us what to load on the truck. You get a two-hour arrival window, and we text when the crew is 20 minutes out.

02

Inspection and Mapping

On arrival we run a moisture meter and thermal imaging camera across the affected wall, ceiling, or floor. A boroscope inspection camera checks inside cavities. This takes 30 to 45 minutes and tells us the true footprint, which is almost always larger than the visible stain.

03

Containment Setup

We seal the work zone with 6-mil containment plastic sheeting and zip-wall doors, then place air scrubbers with HEPA filters and a negative air machine. This keeps spores from drifting into the rest of your house while we work. Setup runs about 45 minutes on an average job.

04

Removal and Cleaning

Contaminated drywall and insulation come out and get bagged. Structural framing gets HEPA vacuuming, then an antimicrobial solution such as Concrobium or Benefect, followed by an encapsulant coating where needed. A 200-square-foot job usually takes one full day.

05

Verification and Clearance

We run a spore trap sampler inside the containment and one outside as a baseline. If the indoor count is not at or below outdoor levels, we clean again at no extra charge. You get the lab results and a written clearance summary within 24 to 48 hours.

Tools & methods

Tools and Methods We Use on Every Job

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture Meter and Thermal Imaging Camera

Finds hidden moisture behind walls and under floors without cutting. We use both together because a thermal camera shows the temperature difference and the meter confirms the reading.

Boroscope Inspection Camera

Slips into a small drilled hole to show us inside wall cavities, subfloors, and HVAC chases. This is how we find mold that a visual inspection would miss.

Air Scrubber with HEPA Filters

Runs continuously inside the containment to capture airborne spores. We use Abatement Technologies units on every job and change filters between stages.

Dri-Eaz Dehumidifier and Phoenix Restoration Air Movers

Pulls residual moisture out of framing and subfloor after removal. Drying the structure is what prevents the mold from coming back.

Fogging Machine

Applies antimicrobial solution into wall cavities, HVAC chases, and other spaces a sprayer cannot reach. Used after HEPA vacuuming, before encapsulation.

Dry Ice Blasting Machine

Removes mold from framing, brick, and concrete without water or abrasive media. Fast, no residue, and safe on structural surfaces that cannot be replaced.

Spore Trap Sampler

Collects air samples before and after remediation. Lab results give us spore counts and species identification, which is how we prove the job worked.

Real results

Before and after.

Bathroom Wall Black Mold Removal

Before

A 60-square-foot bathroom wall in Sylmar Terrace showed black mold growth along the base of the shower. A slow supply-line leak had been feeding it for weeks. Moisture readings hit 28 percent in the drywall and 22 percent in the framing behind it.

After

We removed the contaminated drywall, HEPA vacuumed and treated the framing with antimicrobial solution, and applied an encapsulant coating. Post-remediation testing showed indoor spore counts dropped from 4,200 to 380 spores per cubic meter, below the outdoor baseline.

Crawl Space Mold After Winter Rain

Before

A 900-square-foot crawl space near the Pacoima Wash Area had fallen insulation and visible mold on the joists after a wet winter. Musty odors were coming up through the floor into the living room. Moisture content in the joists read 24 percent.

After

We removed the fallen insulation, HEPA vacuumed the joists, applied antimicrobial solution, and installed a 6-mil vapor barrier. Two days later, joist moisture content read 12 percent and the air test passed on the first run.

Attic Mold and Insulation Replacement

Before

A 1,100-square-foot attic on Foothill Boulevard had mold on the roof deck and rafters after a roof leak. Contaminated insulation was spreading spores through the HVAC system every time it ran. Attic temperature during inspection was 118 degrees.

After

We removed the contaminated insulation, treated the framing with antimicrobial solution and encapsulant coating, and replaced the insulation with new batts. Post-remediation air testing showed indoor counts at or below outdoor levels in all rooms.

Problems we solve

Mold Problems We Solve Across SYLMAR

Most SYLMAR mold calls trace back to one of a handful of causes. Here are the ones we see most, and what happens if they sit.

Ask a pro →
01

Black mold growth behind bathroom walls

We cut an inspection opening, confirm the species with spore trap sampling, then remove the contaminated drywall and treat the framing. A 60-square-foot bathroom wall typically takes one day, including containment and clearance testing.

↗
02

Crawl space mold after winter rain

We remove fallen insulation, HEPA vacuum the joists, apply antimicrobial solution, and install a vapor barrier to stop moisture from returning. Most SYLMAR crawl spaces take one to two days and include a post-job air test.

↗
03

Attic mold from roof leaks and heat

We test the roof deck and rafters, remove contaminated insulation, and treat the framing with antimicrobial solution and encapsulant coating. We also flag the roof leak so it gets fixed before the mold can return.

↗
04

HVAC mold contamination spreading spores

We isolate the system, clean the air handler and accessible duct runs with HEPA vacuums and antimicrobial solution, and run a fogging machine through the ductwork. Clearance testing confirms the air is clean before we close the job.

↗
Proof you can check

Licensed, Certified, and Verified

✓
IICRC CertificationInstitute of Inspection, Cleaning and Restoration Certification
✓
ACAC CertificationAmerican Council for Accredited Certification
✓
EPA Mold Remediation Guidelines ComplianceU.S. Environmental Protection Agency
✓
California Department of Public Health Mold GuidelinesCalifornia Department of Public Health
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
Good questions

Frequently Asked Questions About Mold Remediation in SYLMAR

(833) 929-5837 →

Most SYLMAR jobs run $1,200 to $4,500 in 2026, with small bathroom or attic jobs at the low end and full crawl space or multi-room jobs at the high end. Testing, containment, removal, and clearance sampling are included in that range. Factors that push the price up include square footage, how deep the mold reached into framing, and whether we need to remove and replace drywall.

Start by checking for IICRC certification and a state contractor license, then ask whether they do post-remediation testing in-house. A company that only removes mold without verifying the air is only doing half the job. We provide both, plus a written scope and lab results. Call (833) 929-5837 and we can usually inspect the same day.

Yes. We run emergency mold remediation near me SYLMAR 24/7 for active leaks, post-flood mold, and sewage backups. Call anytime and a crew gets dispatched, not an answering service. For non-emergency jobs, we schedule same-day or next-morning visits. Night and weekend emergency calls carry the same upfront pricing as daytime work.

Same day in most cases. Call before noon and a crew is typically on site within two to four hours. Containment goes up within 30 minutes of arrival, and removal starts the same visit. If you need mold cleanup near me with free estimate SYLMAR California, we can inspect and quote in one trip so you are not waiting on a second appointment.

Ready when you are

Need Mold Remediation near me in SYLMAR, California Today?

Call (833) 929-5837 and we will dispatch a certified crew, usually the same day. Free estimates, upfront pricing, and post-remediation testing included. We are licensed, insured, and have served SYLMAR since 2021.

Get Free Estimate (833) 929-5837 →
Request an appointment

Contact Our Sylmar Team

Call (833) 929-5837 or send us a message and we will get back to you the same day. Our phones are answered 24 hours for emergencies, and regular inspections are scheduled Monday through Friday. Tell us what you are seeing or smelling, and we will tell you what the next step is.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837