We kill the mold, dry the wood, and seal the crawl space for good.

Crawl Space Mold Removal in SYLMAR, California

Crawl Space Mold Removal in SYLMAR, California is what we do when your floors feel spongy, your house smells like a wet basement, or your last inspection found black mold growth under the subfloor. We handle under house mold remediation SYLMAR California for homeowners on Foothill Boulevard, Dronfield Avenue, and everywhere in between. If your crawl space is damp, we find the water source, remove the mold, and stop it from coming back.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Local Mold Remediation Service team in SYLMAR
Careful work. Honest options.
About this service

What Crawl Space Mold Removal in SYLMAR, California Actually Involves

Crawl Space Mold Removal in SYLMAR, California is the process of containing, killing, and physically removing mold growth from the wood framing, subfloor, joists, and insulation inside the space under your house. We start with a moisture meter and thermal imaging camera to map the wet zones, then set up a containment barrier so spores do not drift into your living room. From there we HEPA vacuum the surfaces, apply antimicrobial solution, and treat the wood with an encapsulant coating. It is not a spray-and-pray job. Every affected board gets inspected, and every moisture source gets fixed before we call it done.

Most SYLMAR homes built before 1980 sit on raised foundations with original redwood or fir subfloors. Add decades of irrigation leaks, a slow drain line drip, or a plumbing leak under the bathroom, and you have the perfect environment for crawl space mold. We see it constantly after winter rains when the Pacoima Wash area soil stays saturated for weeks. If you have been searching for crawl space mold inspection near me SYLMAR, that is usually the first sign: a musty smell in the hallway or allergies that get worse when the heater kicks on. We test the air, find the colony, and write you a report you can actually read.

  • ✓ Healthier Air Upstairs
  • ✓ Stops Wood Rot Cold
  • ✓ Fixes the Water Source
  • ✓ Encapsulation That Lasts
What's included

What Is Included in Our Crawl Space Mold Removal Service

Every crawl space mold job includes the same core steps: inspection, testing, containment, removal, treatment, and clearance testing. If you need encapsulation or a dehumidifier, we quote that as part of the same job. Here is what you get when you hire us.

✓

Full Crawl Space Inspection

We crawl the entire space with a moisture meter, thermal imaging camera, and boroscope inspection camera. Every joist, subfloor panel, and insulation batt gets checked. You get photos of everything we find.

✓

Air and Surface Testing

We take air samples with a spore trap sampler and surface samples from visible growth. Samples go to a certified lab and results come back in 24 to 48 hours. That report tells you what species you have and how bad it is.

✓

Containment and HEPA Vacuuming

We set up a containment barrier and run air scrubbers with HEPA filters to keep spores out of your living space. Every affected surface gets HEPA vacuumed before we apply any chemicals.

✓

Antimicrobial Treatment and Encapsulant

We apply antimicrobial solution to kill the mold, then coat the wood with an encapsulant coating that seals the grain. We use products from Fiberlock, Concrobium, and RMR Solutions depending on the surface.

✓

Vapor Barrier and Dehumidifier

If your crawl space has exposed soil, we lay 20-mil reinforced plastic sheeting and seal it to the foundation walls. We also install a Dri-Eaz or Phoenix Restoration dehumidifier sized for your square footage.

✓

Clearance Testing and Report

After the work is done, we run a new set of air samples and compare them to the baseline. If the numbers are clean, we email you a clearance report. If not, we re-treat at no extra charge.

How it works

Our Crawl Space Mold Removal Process in SYLMAR

01

Inspection and Testing

We crawl the space with a boroscope inspection camera and moisture meter. We take air samples with a spore trap sampler and surface samples from visible growth. You get a written report with photos and lab results within 24 to 48 hours. This is the crawl space mold testing with report SYLMAR California homeowners need for insurance or real estate.

02

Containment Setup

We seal off the crawl space access with containment plastic sheeting and run a negative air machine so spores cannot escape into your home. A containment barrier goes up around the work zone. This step takes about an hour on a typical 1,200 square foot crawl space.

03

Mold Removal

Technicians in personal protective equipment and respirators HEPA vacuum every affected surface. We use dry ice blasting machine equipment on tough framing and joists, then apply antimicrobial solution. All debris goes into sealed bags and out of your house. This is the loudest, dirtiest part of the job and usually takes one to two days.

04

Treatment and Sealing

We fog the entire space with a fogging machine using Benefect or Concrobium, then coat the wood with an encapsulant. If you opted for full encapsulation, we lay the 20-mil liner and seal it to the foundation walls. This locks in the result and blocks future moisture.

05

Clearance Testing

We run a post remediation mold testing check with a new spore trap sampler and compare it to the baseline. If the numbers are not where they need to be, we re-treat at no extra charge. You get the clearance report in writing, usually within two business days.

Tools & methods

Tools and Methods We Use for Crawl Space Mold Removal

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture Meter

We use a moisture meter to find wet wood and drywall before we start. It tells us exactly where the water is coming from and how far the moisture has spread.

Thermal Imaging Camera

A thermal imaging camera shows temperature differences that reveal hidden moisture behind walls and under insulation. It helps us map the problem without tearing everything apart.

Boroscope Inspection Camera

A boroscope inspection camera lets us see inside joist cavities and behind foundation walls. We use it to confirm mold growth in areas we cannot reach by hand.

Air Scrubber and HEPA Vacuum

We run air scrubbers with HEPA filters during the job to keep spores out of your living space. A HEPA vacuum removes mold from surfaces without spreading it into the air.

Fogging Machine

A fogging machine applies Benefect or Concrobium to every surface in the crawl space. It reaches areas a spray bottle cannot, including the tops of joists and the underside of the subfloor.

Dry Ice Blasting Machine

A dry ice blasting machine removes mold from framing without water or harsh chemicals. It is fast, clean, and safe for older wood that cannot handle abrasive methods.

Spore Trap Sampler

A spore trap sampler collects air samples before and after remediation. We compare the counts to prove the job worked and give you a clearance report.

Real results

Before and after.

Subfloor Mold After a Bathroom Leak

Before

A slow leak under a bathroom in Sylmar Terrace soaked the subfloor for months. The homeowner noticed a musty smell and soft spots near the hallway. Air samples showed elevated spore counts inside the house.

After

We contained the crawl space, removed the mold from the joists and subfloor, and treated the wood with antimicrobial solution and encapsulant. Post remediation mold testing showed spore counts back to normal. The floor felt solid again.

Full Encapsulation on a 1950s Home

Before

A 1,400 square foot home near Dronfield Avenue had exposed soil and no vapor barrier. The crawl space smelled musty year-round, and the joists had visible black mold growth. Humidity readings were above 70 percent.

After

We removed the mold, treated the framing, and installed a 20-mil reinforced vapor barrier sealed to the foundation walls. We added a Dri-Eaz dehumidifier sized for the space. Humidity dropped to 45 percent within a week.

Post-Flood Mold Cleanup Near the Pacoima Wash

Before

After a winter storm, a home near the Pacoima Wash Area took on water in the crawl space. Within three weeks, mold covered the insulation and the lower joists. The homeowner called us after noticing a strong musty odor.

After

We removed the contaminated insulation, HEPA vacuumed the framing, and used a dry ice blasting machine on the joists. After treatment and fogging, clearance testing showed clean air. The whole job took four days.

Problems we solve

Crawl Space Problems We Solve for SYLMAR Homeowners

Mold under the house shows up in different ways depending on the home. Here are the most common problems we see in SYLMAR and how we fix them.

Ask a pro →
01

Musty smell that will not go away

We find the mold colony, remove it, and treat the wood with Benefect or Concrobium. We also run a fogging machine to reach areas a spray bottle cannot. Most customers notice the smell is gone within 24 hours.

↗
02

Soft or spongy floors near the bathroom

We inspect with a moisture meter and thermal imaging camera, remove the mold, and treat the framing. If the wood is too far gone, we flag it for replacement and give you a clear scope of work.

↗
03

Allergies that get worse at home

We test the air with a spore trap sampler, compare indoor and outdoor counts, and remove the source. After remediation, we run a post remediation mold testing check to prove the air is clean.

↗
04

Mold came back after a previous cleanup

We fix the water source first, then remove the mold and encapsulate the space. A 20-mil vapor barrier and a properly sized dehumidifier stop the cycle for good.

↗
Proof you can check

Licensed, Certified, and Accountable

✓
IICRC Certified FirmInstitute of Inspection, Cleaning and Restoration Certification
✓
ACAC Certified Indoor Air Quality ProfessionalAmerican Council for Accredited Certification
✓
EPA Mold Remediation Guidelines ComplianceU.S. Environmental Protection Agency
✓
California Department of Public Health Mold GuidelinesCalifornia Department of Public Health
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
Good questions

Frequently Asked Questions About Crawl Space Mold Removal in SYLMAR

(833) 929-5837 →

Most crawl space mold jobs in SYLMAR run $1,800 to $6,500 in 2026, depending on square footage and how far the mold has spread. A small subfloor mold removal for homeowners SYLMAR CA with limited growth might land near $1,800. Full encapsulation with a dehumidifier on a 2,000 square foot home runs $5,000 to $6,500. We quote flat rates after inspection, so you know the number before we start.

The three main causes are plumbing leaks, poor drainage, and high indoor humidity. SYLMAR sits in a valley where winter rain soaks the soil and summer heat pulls moisture up through the foundation. Add a slow drip under a bathroom or a broken irrigation line, and you have mold within two to three weeks. We see it most often after the first big rain in November or December.

Yes, in most cases the musty odor disappears within 24 to 48 hours of the final fogging treatment. The smell comes from mold spores and microbial volatile compounds. Once we remove the colony, HEPA vacuum the surfaces, and treat the wood with Benefect or Concrobium, the source is gone. If the odor lingers, it usually means we missed a moisture source or there is mold in the HVAC system.

Encapsulation is not always required, but it is the best way to prevent mold from coming back. If your crawl space has exposed soil and no vapor barrier, ground moisture will keep feeding new growth. We recommend a 20-mil liner and a dehumidifier on most SYLMAR homes. If you already have a working vapor barrier and good drainage, we may just treat and seal the wood.

Ready when you are

Get Crawl Space Mold Removal in SYLMAR, California Today

If you smell something musty or your floors feel soft, do not wait. Mold spreads fast once the moisture is there. Call (833) 929-5837 for a same-day crawl space mold inspection in SYLMAR. We test, we quote, and we fix it right the first time.

Call Now (833) 929-5837 →
Request an appointment

Contact Our Sylmar Team

Call (833) 929-5837 or send us a message and we will get back to you the same day. Our phones are answered 24 hours for emergencies, and regular inspections are scheduled Monday through Friday. Tell us what you are seeing or smelling, and we will tell you what the next step is.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837